How do you scrape and stand behind the searchlights, and how can you direct yourself?

The searchlight is a lighting device designed for external and artificial lighting on the golem's surface. For the installation on such equipment, on the site, on the installation, a special bracket for the spotlight was used, which is in some way in accordance with the method on fixing the product to the element on the wall or special design.

Containment: 1. Kakvi sa scrape for spotlights 2. How do you direct the brace yourself

Kakvi sa scrape for spotlights

If you install floodlights or uplighting, you can't and direct them without mounting brackets. In such a case, the product can be mounted kato glavata on a support or on top of the page surface.

Nai-disseminate in tazi the product category of modification, naming the loss, and design from the type "crown".

T-shaped model and method on a fixed top of the support

Crossbar from follow the typical:

• "L" - characterizes everything from the height to the construction and the overhang on the page tape, at the top of the self-mounting lighting of the body. They throw on the illumination of the body depending on the technique of geometric dimensions and thickness;
• "T" - assuming it was placed on the pole of the source on the light and it is characterized with the size of the deviation on the camp;
• "V" and "H" - all characterize with size on the overhang on the ridge, project it on top of the self-assembly.

When constructing from the “crown” type (directed under the format to the circle), it is assumed that they will put up a pole or a floodlight.

Design on the crown on the mast for clarification

It is fixed on the staple of the support for the clarification (mast) and it can be perverted in some way starting:

• with the help of a bolt, fixed this is a twist with a bolt;
• xom, wear nuts and washers;
• method on the flange, fixing all the kinks with bolts and nuts.

With different manufacturers, they named a series of brackets for floodlights, so when choosing a design, carefully read the proposals and choose the right model.

Modern LED spotlights Those se are notable not only with good light characteristics, but also with a low temperature, somehow with small geometric dimensions. These indicators allow you to set up a light source on the bright top of such a structure, some of it from your own country, allowing you to achieve high-quality clarification on the ground at a tyahnoto place.

Design on a bracket, especially for LED spotlights with low heat, can be fixed, rotating and crawling on the crack.

Options for fastening to brackets with the help of brackets at the top of the support with different cross sections

Sometimes they put the lighting bodies on top of the façade on the fence, they perform functions for lighting on the adjacent territory, and still they serve as lighting for the construction, top of some of the installation.

In the basin, the design on the staple for the façade may be different.

Some of the options are possible for such a design, intended for mounting on the vent on the bright top of the wall, as shown in the following figure:

Scobie for mounting vertically on the surface (on the façade on the fence) back kjm sdzharzhanieto ↑

How do you direct the brace yourself

Nay-lesniyat start and direct the bracket behind the LED spotlight e, e lek and not from the golem of the metal section of the structure.

If the consumer knows how to work with the welding equipment and hand-held electrical tools, then the next figure is shown:

Bracket from the profile pipe and metalen ygl

Work on production on Tosi model is perverse, somehow following:

• this detail is torn from a profile square pipe with a cross section of 40 × 40 mm, which should correspond to natural lighting (lighting, locally, generally, etc.), some kind of floodlight and osiguri;
• each detail is scratched from metalen gl gl ss section 40 × 40 × 4 mm, length of mu treabva and compliance with the length of the length for the length of the spotlight, intended for installation;
• the hollows are punching into the detail from the glare, into places, corresponding to open the door to the spotlight;
• a detail with a size of 150 × 150 mm is scratched from a metal sheet with a debelin of 2.0 mm, a trace of something in the ember pierces the mounting opening for fastening to the wall bracket;
• the pieces of the preparation of the workpiece are lumped into a single structure through brewing;
• sglobenate bracket e covered with a layer of soils and a trace of boyadisan.

Option for nai-prostate bracket for installation on the spotlight, made from a metal profile

How to mount a spotlight on the wall

How else to attach the bracket to the wall depends on the material from which the wall is directed.

Ako projector, montiran on brackets, e montiran on top of a darvena is a decent design, then nails or screws for a darvo can and all use some kind of fasteners. Ako stenata e rotten, then use remote or mounting dowels, hammer with the help of specially equipped equipment (screwdriver, pneumatic tool, pistol, etc.). E, as the stenata is concrete, togawa can and be used by the anchors of the bolts.

For your information! If you use expander dowels and bolt anchors, it is not necessary to install them beforehand so that they will punch an opening with a diameter corresponding to the diameter on the fastener.

The design on the bracket for the spotlight can be completely different, especially if it is aimed at the raka. In this case, everything depends on the armor on the searchlight, the availability of material and the imagination of the maistor, some of the work is done.

PreviousProjectorsWhat you need and how to choose an IR illuminator for video camerasNextSearchlightsHow to choose a xenon spotlight or fenerche