Welded and installed on angelic eyes on VAZ 2114
A lot of strange manufacturers decorate the farovete on a car with original clarification, i.e. nar angelic eyes… For pity, the local manufacturers don’t get it right. You can both direct and install it yourself. In the tazi, the article will show you how you direct it yourself, independently install it and turn your angelic eyes on the VAZ 2114.
Containment: 1. How can you direct angelic eyes on VAZ 2114 2. Cooking on the farovet 3. How yes svrzhete kam kabelevaneto VAZ 2114 4. Are you still globbing for prsttenite on the farovet?
How can you direct angelic eyes on VAZ 2114
Contrary to the odds on the VAZ 2114, they didn’t turn, the classic rounds of angelic eyes (AG) look pretty decently in tyah. Therefore, sew on the first hand of the work of the AG, there will be more circles.
Angel eyes with two LEDs
In spite of everything, fix the design with Tozi, comrade vi struva one hundred. For yes, implement the project, check out the tryabva:
- Two round plates made of plexiglass with a diameter of 8 mm and a length of 400 mm.
- All four super bright LEDs with a diameter of 5 mm.
- Four resistors of 1 kΩ each.
You can buy LEDs and resistors in any specialty shop or radio pazar. The price for asking a few dozen rubles. It’s a little bit bad, but reshavam and tozi problems. In the store they sell bastuni for shori, but you can buy solid ones without a hollow in the door. Usually those gardens are 1 m long, so only enough for two AGs.
Bastunt beyond the blind is ideal for our AG
From the instrumentation, nothing is necessary:
- Punch with a drill with a diameter of 5.5 mm (if possible).
- Hacksaw for metal or brocade knife for trion.
- Ticks.
- Poyalnik.
- Technically Seshoar (if possible).
Materials:
- Sealant
- Insulating tape.
- Heat-sealed pipes with different diameters (if possible).
- Conductors.
On the first place, tryabva and direct the wall. For VAZ 2114, those trips and sa with a diameter of no more than 90 mm. Designate metal cutia with a suitable diameter and a hollow in the stenata and along the diameter on the right. Fasten the burkana, for example, in a mengem or on a different beginning. Drive the unity edge on the right side of the opening in the direction of the opening and close it and then heat up the seshoar close to the samata kutiya. First of all, with a plexiglass camp of plastics, fire it up and in some time you will move the seshoar over it.
Ogvane na pryta v prysten ss sesoar
In case you need a sesoar, you can use the whirling water. Float the water in the water and turn into a plastic camp, I’ll see you around the burkan with two tongs.
Ogvane na pryta with whirling water and pincers
Now cut off the excess prjt with a hacksaw, such as in the wall and here, forming a praznina from about 10 mm - and get ready to cook. Let the time be clear with the LED. Intention to anodite (initially anode conductor e-long from the cathode) and sing the resistors to the tyah.
Resistor trebva yes bydat soldering kam anodite on the LED
Now, say the cathode, svyarzvame gi in deuces and drunkenness of the conductor - otherwise, the “minus” is stored.
Connected to LEDs in twos
The slug is thermally twisted on a resistor, the diode is designed in such a way that it looks at different slopes, and the distance between the ties is about 8 mm (see the picture along the bottom).Follow the connection to the conductor on the resistor and drink the positive conductor to the switches.
Molding twin LEDs
Now sa break open into the edges on the prustenite with a diameter of 5.5 mm and a hole of 8 mm. Drop a cap of nitro polish or colorless polish on your nails anyway and put on an LED. Ako nemate the drill, you can fix the LED on the spot with a thermocouple, but for the sake of sluice in the right place, even more trebva, and then increase it with a hacksaw.
Slobe and prepare for slobyavane angelic eyes on VAZ 2114
Ostava yes, they will send small packages with a length of 0.5 mm to the top of the angel's eyes. It is through the tyah of the light from the trabat that it is extinguished.
Propylene AG for VAZ 2114
According to the principle of everything is ready, it's time to check the AG in operation. For yes, send a friend, wire a Krona battery, a battery for a stake, or any other device with a voltage of 9-12 V.
Checking on angel eyes on VAZ 2114
Tova e vsichko. It's time to put AG in the farovet on the VAZ 2114. For the goods of the farovet, all dismantled, glass, attached to four keys, all removed from the tyah. Another modification on the headlight and the glass is planted at the top of the sealer, carefully and diligently flooding the glass with a technical seshoar. The trace of the cat sealer is omekne, the glass can be forested and removed, the trace of the cato se is torn off with a screwdriver.
Headlight VAZ 2114 ss knocked down glass
Install the angel eyes on the spot and fix the frame with a sealant, pre-carvey protecting the conductor of the opening, directed to the reflector. Using a key or seal (depending on the modification to the headlight VAZ 2114), mount the glass on the meat.
Headlight VAZ 2114 with an installed angel's eye (used "eye" for industrial production)
Another look like this:
VAZ 2114 with prusten AG
Now we’ll sort out for some time how the worms of the krgove sa are juicy on a snapshot along the mountain. These circles show the location on the wall, but the step foe on the AG doubles and decided to put it exactly like that on your VAZ. For yes, send Comrade, take it apart, tryabva and send a friend a set of messages. More out of sight of something kato tov:
VAZ 2114 with twin angelic eyes
Angelic eyes with LED lamp
Ako don't be shy about turning angelic eyes, then you can send AG to your VAZ 2114 with any form. For yes, send tov, tryabva and use a special gavkava LED trba, intended for tuning on cars.
LED request for car tuning
You can, yes, with different lengths, so there is unlimited scope for the imagination. For some reason, let’s put a pipe around the perimeter on the reflector on the VAZ 2114 headlight. So we’ll decoction the headlight and go with a topline gun (you can even screw it with a screw) around the perimeter on the reflector on a special fastener element, which comes with tape. The necessary fasteners are required, as this LED tube is practically not glued with a heat gun. Fixing the tape in the montage, izvodame zhitsata from the headlight.
Angelic eyes on VAZ 2114 from LED gavkava trba
Another look like this:
VAZ 2114 with angelic eyes from LED tube
Sealed page LED strip back kjm sdzharzhanieto ↑
Cooking on the farovet
Ako nyamate desire and se occupied with independent production on angelic eyes for VAZ 2114, you can buy and cook.Tova, sort it out, it’s a bit more sharp, but it’s all right, somehow tryabva and direct it, yes you mount it in the farovete and yes you swirl, it’s even difficult for everyone to own a car. Today's date in the store, you can try three types of angelic eyes for VAZ:
- Gas discharge.
- On SMD LEDs.
- Groupirani.
Discharge the fluorescent tubes by directing them under the format onto plates of one size or another. Tj kato gas-discharge lamps se protect from high (voltage and more) voltage and short circuit a special system for zapalvane, the ballast is usually delivered from takiwa to the eyes.
Angelic eyes with gas discharge
SMD angel eyes behind VAZ with a globe from a separate LED, located on a wall scarf. Thus, the design, for the difference from the gas discharge tube, is not an insurance against shock and vibration, but from the point of view of the series from the point (gas discharge tube giving unpredictable light). Ako look for da imate “dotted” angelic eyes, togava SMD tip e tova, from something you need.
Angelic eyes for VAZ, globe on SMD LEDs
Cluster angelic eyes with all the LEDs, but those are not the top of the separate diodes, but the top of the COB matrix is a lot of microdiodes, with ordinary phosphorus. Thanksgiving on Tosi design, cast angelic eyes on the VAZ, like a gas discharge, give a stable light.
Two-tone angelic eyes on the VAZ
Cluster devices can and do not just light itself - depending on the design on the matrix. You can often see the clusters of the device behind the VAZ 2114 with a spiral, orderly dotted radiance.
LED and cluster angelic eyes for VAZ and 12 V for safekeeping, for some reason they need a voltage stabilizer (in a burgundy voltage, it can reach 14.5 V). Some manufacturers add their "eyes" with stabilizers.
How yes svrzhete kam kabelevaneto VAZ 2114
Angel's eyes are gloomy and montirat, leave and gi you will turn correctly to the VAZ 2114 verigata. But if you look for it and turn it on regardless of other lighting devices, you can even cut a burgundy mesh through a separated bud, which can be located in any convenient place on the reinforcement panel. Panel VAZ 2114 dori and place for installation on additional butoni.
In a worse way, it’s whitened, so in a burgundy merge on a VAZ car and a lamp with a size of varia between 12-14.5 V, dokato LED eyes, including those, pointing to a pipe or tape, they need from strictly 12 V. It’s disgusting the case will still cover a few days of exploitation. On the other hand, let's turn on the angel's eyes correctly - through the regulator for tension.
Exclusion of the right AG on the VAZ 2114, which is equipped with its own stabilizer. For such is the "eye", disassemble it, it is not necessary, but the rule is the stabilizer.
Nay-lesniyat start e yes sloit so the stabilizer at the top of the integrated microcircuit, for some reason it offers all the shops for radio components and a stream of about 20 rubles. Commodity KR142EN8B (alien analogy ESG7812P, MC7812, L7812CV).
Chip KR142EN8B and negovyat izvod, kadeto:
- 1 - input;
- 2 - general;
- 3 - exit.
The verigata on the regulator for warning is as follows:
The circuit for the voltage regulator is for LED angelic eyes
A microcircuit on the stabilizer is shaking and put a small (5 x 5 cm wide) radiator on top or a screw and metal parts on the car. In the latter case, you will be sure that the microchip was stuck to the metal plate, and the metal itself was not shaky and would be boyadisan. One such stabilizer can save and shine like an angel's eyes. For yes, send tov, those tryabva and bdat svyarzani in parallel.
Ako washta setting foreseeing the installation on four angelic eyes, togawa tazi scheme can also do it.
And this is another, more interesting scheme for the stabilizer, for some reason, yes, let the angel’s eyes “disappear”, when you turn it on:
Stabilizer with automatic brightness control for angelic eyes
Dokato farovete on long or turn off the light line, the transistor VT1 is not closed, and the stabilizer DA1, instead of 12 V, giving a low voltage, somewhat dependent on the position on the trimer R2. Angelic eyes are working with painted brightness. Firstly, turn on the long or short light lines, open the transistor more tightly and at the output of the stabilizer, the mood will rise to 12 V. The angels shine cleanly with full strength.
Instead of VT1, all silicon transistor with low power from n-p-n structure can work. Reguliranetto on the verigata is fresh to set on the desired brightness on the angel's eyes with the exception of the farove. Produce this, somehow climbing up the mountain, through the winding on the trimer R2.
Are you still globbing for prsttenite on the farovet?
For example, it’s a lot of seriousness and tryabva, yes, it’s still allowed to go ahead and mount the angel eyes on the VAZ 2114. Let’s answer decoctions and four (yama and give numbers on the member of the Administrative Code and GOST - don’t tell them to think, they themselves will decide) :
- All fronts of light lines and light reflectors on the car are shaking and white at any color temperature.
- At the expense of the means of production, it is allowed to install lighting devices from other models.
- Food has been taken away, even though it is managing a great means from the direction of the exchange, which is not foreseen in the project.
- All food is taken away when driving a car with a light device, which is self-modifying, which is not foreseen from the design on these light device.
Prvata and the second point, by principle, work for the VAZ 2114. But this, the third and fourth yama, yes, they can do it, dory, put Markov and white “eyes” in a specialized service. Okazva behold, why else would the globe be behind independent angelic eyes? No, yama yes fuck the globe. According to the legislation in force, farovete you will simply be more likely to change, and you yourself will still be turned into a pedestrian, somehow depriving you of the rightness and manage the exalted means for a pole of a month or a year.
Here we can join. Now you know how to direct your angelic eyes to your own right and yes, install it in the farovet on the VAZ 2114.
PreviousDecorative lighting and customization How to install angelic eyes on the VAZ 2110NextDecorative lighting and customization Installed and connected to angelic eyes on a vaz 2107