How to install and wire DRL on Ford Focus 2
DRL doesn't seem like a necessary lighting device, but CAT doesn't think so. And with tyah, it’s safe - see the distance from the distance, why move the kolata, and remove the parkiran from the five. In Tazi, the article is independently equipped with the Ford Focus 2 restyled from daylight.
Containment: 1. Research on normative documents for daily light lines 2. Differences between predi and trace restyling models 3. How to put the DRL and where to put it on the Ford Focus 2 4. Installation Instructions 5. Scheme on the wire
Research on normative documents for daily light lines
Nyama and izbrayavame in detail all the regulators of the document, tie with the daylight line, but just remember the research, set out in ty:
- lampi type - all kinds;
- bloom - beat from every nuance;
- bright intensity for each lamp - 400-800 cd;
- Working with DRL is good night, with the inclusion of a long light line, a light line key, a light line page or PTF, it is not taken;
- automatically switched on, once the key is turned on, it is in a position that does not exclude the operation of the engine;
- the height on the stand above the spot is paid - not a little from 250 and not more than 1500 mm;
- remove the distance to the DRL of the lamp - no more than 400 mm;
- the distance between DRL light lines is a little 600 mm.
General search for location on the day light line back kjm sdzharzhanieto ↑
Differences between predi and trace restyling models
The second generation of the Ford Focus is produced from 2004 to 2011.According to the principle of that se, the view of the colata is straight to the point: champovane on the vratite, relief kapak, format on the farovet, the long grille on the radiator has been easily changed, and the so-called.
Ford Focus 2 dorestyle
Ford focus 2 restyling back kjm sdzharzhanieto ↑
How to put the DRL and where to put it on the Ford Focus 2
Ima some options for choosing:
- work on the farovete for kasi light lines, such that they work in DRL mode;
- use the farove for the mist in rollata on the DRL;
- install daily lights separately light device for PTF capaca;
- Install the DRL with a separate device at the bottom of the radiator.
Installation Instructions
For the sake of the fact, why are there few options for installing daylight lines on FF2, let’s take a look at all the methods one by one: installing before PTF, in the radiator at the shaiga and processing for a dark line in the light line.
DRL to PTF
Nay-lesniyat start yes, buy ready linings from the veche install daylight lines. Osventova, kogato gi kupuvate, it’s necessary and take it foresee how the modification on the Ford Focus 2 imame - restyling or dorestil - is visible and the format on the lining depends on the goods. The installation operation itself and the diagram on the link will still remain for any modification to the vehicle.
PTF surcharge from daylight hours for Ford Focus 2 Restayl (2008-2011)
How do gi installers? It is exceptionally simple to install daylight lines on such a day - premahvame old kapatsi, montiram novi. Hvarlyame conduct from the fenerite to the engine compartment. For yes, dump the capac, you also need a flathead screwdriver. Ako imam dorestil, togava parvo pridrpvame and premahvame "beware" - those sa attach to them and use keys. Duplicate the key and click on the image along the -line of the arrow mark.
Premahvane on "vedi" on PTF Ford Focus 2 dorestyle
After eating the beginnings of the kapak and the gosvalama - the one attached to it, absolutely eat the keys.
Premahvane for facing on PTF Ford Focus 2 dorestyle
Ako imame restyling, that yama know, just skip the naslagvaneto.
Premahnato slapped for PTF on Ford Focus 2 Restayl
The question of technology remained. Lead the precarvame to the engine compartment together with the cable from the PTF, shrakvame värhu novia kapak and cook.
Installing substrates for PTF with daylight (FF 2 Restayl)
DRL on the radiator
Tuk on the principle of nyama is a lot more work. Nie kupuvama something like:
Daily light lines in the radiator for the Ford Focus 2
Anyway, it’s convenient to start (double-sided tape, sealant, gun for sculpting, etc.) by attaching the fenerite to the slots on the shield. Mostly with takiwa lampi se includes dory fasteners elements.
Days of light, montirani in the radiatornata shaiga Ford Focus 2
PTF or switch light to DRL mode
In the Tozi mode, the Farovete for the kasi light line or the Farovete for the darkness act like daylight hours. Distinct from the standard mode, the headlight or light glare will turn on automatically when turned on on the igniter, and the headlight will work without a light glare for a short time.
The car is not a product of a special modification, the only thing that is disreputable and all will put economically lower power in the PTF. Daylight svetlini nyamat special studies for the format on the lightlinniya luch (contrary to what the norm is: horizontally - 20 degrees to the side and navn, vertically - 10 degrees above and below the horizontalat). Let's also choose LED bulbs with a H11 base with a low power (6 W) and a light flux of 600 lm (light intensity is approximately 550-600 cd).
6W mugs H11
In general, yama and izvarshvame a mechanical revision on the farovet for kasi svetlini, ty kato those tryabva and work correctly for their intended purpose.
Once again, change the PTF, try and get ready, as soon as we get on the daylight, we destroy the farovete for the darkness.
Scheme on the wire
Leave and get the daylight lines on our Ford Focus 2, so they work in accordance with the regulatory documents (see the section “Regulatory Documentation and Daytime Lighting Studies”). Let's save some time with the tezi, koito byah installirani to PTF or to schaygata.
Linked to DRL, away from separate device
For yes, we’ll connect the light line of a burgundy wire, we need from a pet-pin (winding and one group for switching on) a relay with voltage to react 12 V. For example, a relay for a long time or a light line from any 12-volt stake is suitable. Osvent tova kupuvame block for him.
Relay and unit for linking to DRL
Let's put together the following scheme:
Wiring Diagram
Once it is energized, the voltage will appear at terminal 30 on the relay. Through the normally closed contact of that break, contact 88 - DRL is light. First of all, turn on the page of the light line or light line on the head (including everything with size), in addition to the bobbinat on the relay (shift 86) and the work, this other edge on the bobbin (shift 85) is constantly connected to the earth. Contacts 30 and 88 of opening - DRL is still missing.
Much more important is the assembly of the prepositional switch in the “+, when it is ignited” (relay contact 30) in the case of a connection to the switch in the DRL. For yes, send a comrade, it’s enough to buy a darzhach, some are just a muddled conductor.
Tozi durzhach for prepositioners can be tied directly into the conductor
Let's start with a brighter lightening. For yes, send the comrade, the first time you will skip the panel from the distance. Except for the self-tapping screw, in the picture along the bottom, the point of the arrow is indicated.
Tozi self-tapping screw djrzhi decorative tape under the control of kutia
Izdarpvame panel to itself si to the place, to senamirat klyuchalkite, those are the designations of the arrows.
Premahvane for decorative cladding
Now put the rkata si into the slots to the left of the block (indicated by the arrowhead). From the squeeze, two keys, remove the location and remove the block.
Premahvane on the block for control of external lighting
Izvadame blockiya save the block. Interested in all of the following conductors:
Tezi conductors trebva yes svarzhat contact the relay
Hello. The conductor from terminal 85 to the relay can be wired either to a black conductor, or simply to a socket on a car, which is fastened to a suitable screw.
Get in touch with the conductor. Tova may be with an ordinary investment, without yes, the main conductors will miss it. Clean up the isolation from tyah, zapoyavame gi (not gi zavinvame itself!), Isolirame.
Relay connected for daylight hours
Fixirama relays to any convenient place - and there is enough place for the back of the block for control. For example, let's choose some place before the decomposer.
DRL relay, located before the storage unit
For yes, draw a conductor, without yes gi prekshvat, it’s convenient and use a special knife and block.
Svrzvashch block
Stay and turn the DRL light up. Two conductors remain from the tyah: “minus” and “plus”. Minus the usual sa niello - svyarzvame gi from the coupeto to the colata, for which a screw is suitable for the comrade. You can, for example, take the screws for fixing on the PTF or headlight.Svurzvame positive conductors together, udlzhavame gi and gi preprashame kam salon. Connected to terminal 88 on the relay. Turn it on, check it out. According to the scheme, the DRL will still turn on when it is turned on, and it will go out even more, when it is turned on, size or light on the head.
DRL vazka vz based on PTF
Here the circuit diagram on the connection is still attached, on the 88th contact on the relay itself, do not wire the wire from the DRL, but the conductor from the PTF. You can even try to get a block on a block for control on Vishnat Svetlin. On the picture along the bottom, the conductor is signed with the words “predetermined by PTF”. Izklyuchvame go from the block and go varzvame kjm 88 contact on the relay. E, do not take away and change the standard headlamps in the farovet for the fog with LED from a lower power (see the section "PTF or switch light lines to DRL mode").
Prevklyuchvane on standard PTF km day light lines on Ford Focus 2
DRL mode
Here, the scheme on the connection is slightly different, for which the imam needs from tezi farove to the regime on kasi svetlini (BS). I choose the mode to work on the farovet, somehow as follows:
- zapalvaneto e excluded — BS e excluded;
- the igniter is not included, the switch on the light is in the “off” position - BS is not included, no size;
- “size” mode is not on - size on, BS off;
- BS mode not enabled - size and BS with enabled.
That is, the DRL mode is adding a standard mode. For yes, attach a circuit diagram, a switch for a relay with four contacts 1119-3747210-10 and a jumper with two "t-shirts" - one golyam, a little friend.
Tova e vsichko, some tryabva yes buy, for yes add daylight
Yes, two prepositioners are still needed: for 20 and 10 A.Those can be taken from spare parts and accessories to the mounting block.
Suggest you can take it from the reserve part
Dismantle the mounting block, for some reason protect the capak from it and develop the screw nuts. On the spot, look at the snapshot along the valley, mount the prepaid and releta.
Mounting on relays and relays
Sega premahwame green connector.
Tozi connector tryabva yes bjde premahnat
At the terminal, ask for a snapshot (these are free), mount a jumper from a certain country.
Put a jumper between these contacts (read outward and backward)
Install the greenery connector on the ground, mount the mounting block. DRL vz is based on readiness for the light line.
Important! Next, disconnect the green connector from the mounting block, and also disconnect the main device. For yes, turn it off, enter the PIN code, which you can see in the friendly documentation for the car.
Zatova installirahme daily light lines on our Ford Focus 2. Now the driver of the day has become much safer.
PreviousDaylights How to install and wire daylights on the VAZ 2107