How the LED strip is connected to the computer

Title: LED strip light

LED lighting is considered to be the most popular starting point for lighting for various rooms. Same implementer with with the help of a special LED strip, koito ima a lot of predominance when crawling. One of the advantages of tosi is the method for clarification, which is suitable both for a whole room and for a specific area.

Containment: 1. What is the need for lighting in the computer area 2. Scheme on the wire

What is the need for lighting in the computer area

A personal computer has long been an undivided attribute into every apartment or private house. But tryabva and remember that you work hard on the computer, tryabva and be sure to define the rules for organizing the work place.

An important moment when working on a personal computer is that the backlight is not good and the backlight is correctly made. The need for backlighting on a computer is a shameful night due to the fact that the monitor contrasts with the general space, until it appears scream and tension in the eye.

LED backlight Illuminators on the working raft

Izpolzvaneto on LED tape in the case of bilo beat nay - good option. It is possible that you will swirl the tape, such a beautiful music and sound like a svetlinata. Osventova can yes install the switch and, if necessary, turn off the backlight type on the personal computer. The next step is to figure out how to wire the LED strip of the computer in various ways.

back kjm sdzharzhanieto ↑

Scheme on the wire

The LED tape can be connected either to a personal computer or a laptop.In case of warping for bonded work, it is necessary to correctly calculate all the goods and pay for the ribbon, which is still tied. For example, tryabva yes you know what is stored on a personal computer in a state and deliver a current of up to 5 A, but with a laptop, the figure is low. This is why, if you plan and use a standard LED strip, try and take it foresee that approximately 1 meter of consumer tape is about 0.4 Amperes. Tozi the moment tryabva and see everything foreseen, for yes, you can see it and work stably. Ima standard tape and RGB tape, so the technical circuits on the connection are different. When connecting the LED strip to the computer, 2 wires are used, and the RGB strip is 4.

Required materials and tools

For yes, pervert the installation on the LED strip, try and have a set of tools and various materials, you cannot do without it. Some of these tools and materials:

Poyalnik.
Protected.
LED strip with required size.
Knives.
40 W electric soldering iron.
Electrical conductors with a cross section of 0.75 sq. mm
Zapoyavane "POS-61" and colophon.

This is the main list with materials and tools, without which you can’t and correct, somehow link tape to a personal computer.

How the LED strip is connected to the computer Received a set of tools for working with led

Scheme on a conventional tape

Some of the detailed diagrams are linked to a standard LED strip with a length of 1 meter and a personal computer. The LED tape is not routed to the SMD 3528 LED. To complete this procedure, a 4-pin molex connector is required.It's not difficult to choose this connector, you can even take it from the SATA adapter.

Included is the LED strip, which is protected from 12 volts. Therefore, for the sake of it, you will destroy the computer, you will need to shake the wires and black conductors. Other conductors, worms and niello, are not necessary for tying to tape, so they can be isolated or cut off. On the connected LED tape, it is bleached where the name of the “+” and where the “-” are. Tryabva and svyarzhet "+" kam zheltiya conductor and "-" kam zemyata.

Once again, the procedure is hot, and connect the conductors with a reliable isolation, more shaking and separating the system block. The LED strip with power is larger than consumer 0.4 A, and stored in a personal computer in the state and deliver 5 A, such a thing needs to be harassed, so it is safe enough to store it. Tozi method for linking to LED tape to a personal computer can be used for various purposes.

Scheme on LED connection Approximate diagram on computerized

Scheme for connecting to RGB tape

For the difference from conventional tape, RGB tape is a lot more difficult to connect to a computer. The difficulty lies in the fact that you need 4 pins instead of 2 and you don't need a dedicated RGB controller. You can direct the remote control and more conveniently and control the system.

Important! The RGB controller is a specialized device, which somehow allows for changes in light intensity and nuances in a multi-color device. Scheme on the wire RGB LED strip, which is safe from 12 volts and a length of up to 5 meters.

RGB scheme on the link Scheme for linked on rgb tape

For yes, do not twist it difficultly, you can buy special connectors. I use it for mounting on LED tape.

Predishna LED strip light Next LED strip light How to direct the lamp from the LED strip ss own sir