How to properly fold the LED strip into a stake
Title: Svetlinna LED strip 
In order to install an LED strip in a car, you do not need to have special skills and professional knowledge in the field of electrical engineering. But for yes, do not destroy soar si and yes, get nai-kindness of clarification, it takes time, patience and a little light.
Containment: 1. Species and types of tape 2. Scheme on the installer 3. Materials and tools 4. How can you make a fuss 5. Kjm of the accumulator on kolata 6. Through a resistor 7. Switched on via linear stabilizer 8. Stabilizer switched on via impulse
First and foremost, the question is how to turn LED tape into colata, for the success of the winding, and you know a lot of nuances and tricks. Before you install the tape, try to choose the place for the installation, for some reason, combine it with the point on the link. You can choose any place for your interior lighting, but most of all, cross-panel lighting, for some reason it drains smoothly under the sedalkite and on the hearth on the colata. You can save it or save it or start it up.
Do not take it and check where you can and cut it off.
Species and types of tape
At the time of the pazar for the automatic setting ima a lotLED strip for stake, and those vitchki differ in appearance, density, color, protection from moisture and power. You can choose between two types of backlight - 3 × 2.8, or 5 × 5 mm. The next criterion is to show the light of the lamp on the tape meter. Select the tosy indicator solely from your preference. Lampite can and be put not by itself in one red, but in two.The power on the lamp depends on the amount of energy, some consummation - a bit more powerful than the lamp, they will absorb the charge wisely. The color on the backlight can be monochromatic or with a variable function, sometimes it is adjustable from the switch. There is some degree of protection against moisture behind the lamp, but if you install it in the interior of a car, this question is not very important.
Variations in colors on the LED strip for the car back kjm sdzharzhanieto ↑
Installation diagram
Regardless of where you sign up and install the tape, tryabva and I will save it. Put the ribbon under the toad, then I put it under the saddles, then you will somehow direct the exit to the pedal. As a result, put a lightening of the reinforcement panel on the top of the coma and attach it with a stationery tape. At the place on the gankite of that ryabva, yes, it was torn up and drunken, such that yes, the backlight for tsyalat long. The edge of the tryabva and the connection of the controller, so you bloom on the conductor and fall when connected. Following the correct installation, you can direct the output to the remote control and control the backlight and light music with the remote control.
Approximate diagram for the connection to the backlight for the stake back kjm sdzharzhanieto ↑
Materials and tools
Mounting on LED strip in kolata it doesn’t take much time and effort, but for yes, varvi barzo process and let it be possible to lighten your interior, tryabva and ste tarpelivi and have some tools. For yes, send Comrade, schevi treyabva: colophon, electric tape, knives, connectors, soldering iron, peace of mind, corrugated edges, tool fastened to tape, profile, which is resistant to moisture.It’s like that, for installing the tosi accessories, you need to try directly the wires yourself, the amplifier for the work is done, somehow the controller, which is more dissuaded for distribution to tension. For not exhausting the battery on the car and the system of work without damage during transportation, try to buy storage, something more dissuade in the form of power, density, type and type on tape.
Optimum set from instrumentation to accents back kjm sdzharzhanieto ↑
How can you make a fuss
Tuning in no way starts without trying and swearing to work on the LED itself or work on the battery. For yes, turn on the lamp directly for a flare, shake it up and turn it up to exactly 12 watts or use a stabilizer. A lot of the voltage is still missing the stabilizer and you can still adjust the power to the backlight without harming the general condition of your car.
In a good way, yes, isolate the stabilizer from the hull, there is a lot of heat. But ima and modern stabilizer, which is a search for additional means. With a tyahnoto, the radiator is not crawling, it’s not sensible and work in the normal mode. You can experiment and drink the stabilizer yourself, but there will be a lot in the forest and safely, and buy it in a specialized store, for all the type of lamp with separate stabilizers.
Kjm of the accumulator on kolata
You can either use a direct lamp or use a stabilizer. The operating time depends on the amount of power of the lamp itself and the amount of power of the battery. Ako decide yes gi svarzhete directly, do not take it away, why minus ce with minus, but plus kam plus.Before you buy LEDs, check the brightness level in the store and sieve if you need a bright light, or prefer a long radiance. Spore tozi the principle of LED tape in the trunk is a lot of trouble for installing without additional knowledge and skills.
Through a resistor
Kogato sa installirani, golyam broy LEDs and an additional limiter, called a resistor. The resistor is distributed between the lamp itself and stored, from which they will take energy. Tazi technique help and increase the time for using the LED when properly charged. For yes, choose a resistor and let the lamp turn on it, it’s necessary to count the chain, in some way the si struva and all the foreseeing work on the tape, work on a separate lamp, on the input and output. Carefully take into account the questions and calculate the good verigata, consult with a consultant in a store or an electrician, how to distribute this voltage and how, as a result, you will get depending on the resistor. Exit vines and tryabva yes e 12V. The resistor can be purchased or routed by itself. There are a lot of video clips on the Internet and instructions for step by step for directing to a resistor near the house.
Switched on via linear stabilizer
The line regulator is a direct conductor for electricity from the input to the output. A lot of forest and direct the linear stabilizer yourself, it is important that you follow some rules. For yes, your system and the linear regulator must work, and its function must be fulfilled, it is important that you correctly connect the input - output and set the polarity. Let the tryabva come in and see the world freely, for this tryabva, let the crack from the stabilizer get rid of it and drink it.You will send the exit well and you will sing about it, it’s safe. There is basically nothing polarity in business. Minust trebva even on Wednesday. No matter how fluctuating it is, it saves your voltage, basically, which results in a 12V result, otherwise, service the lines on your lamps and they will paint a lot more.
Connecting the chain through a linear stabilizer back kjm sdzharzhanieto ↑
Stabilizer switched on via impulse
This way it works on a burgundy background on the car, directly depends on the work on the engine, the current can be saved and the varia is significantly and for yes it normalizes the work and yes it saves the lamp with a limited voltage of 12V, you need an impulse stabilizer, which thanks to the impulse at the end of the dava desire indicator regardless of entry and exit. The inclusion of a regulator can be directed as a result of the modification to a linear regulator, which is improved thanks to two transistors. This is the scheme of the solution to help and direct the switch on the regulator near the house.