Installation and connection to LED lighting under the cupboard in the kitchen

Title: Backlight

In the kitchen, somehow in every working place, the kindness of lightening is important. The central lamp cannot be osiguri, but it is protected from stone and syankata pada on the surface. In this case, for lighting, shaking and directing the choice to the floor on the LED lamp, fixing the surface on the hanging cabinet.

Containment: 1. Benefits from installed on LED backlight 2. How to choose LED strip for the kitchen 3. Installation 4. Stupka on stupka process on a joint

Preferences for installed on LED backlight

Illumination with the help of LEDs.

• Little debelina. For the difference from other illuminating bodies, LED strips and modules from debelin 10–20 mm. Tova premahva necessity and borrow a place on a long raft, but just mount the LED at a distance.
• Those can and will be located on the back of the kitchen cupboard and absorbers. Comrade oshiguri evenly illuminated without shade on the work surface.
• Whenever it is used instead of conventional LEDs, RGB diodes can be switched on from blue light, it is necessary for work, when blue light is on duty. Tova turned on all the twists with the help of a timer and a motion sensor. Brightness and color can be brilliantly controlled by a sensor or remote control, protected from a battery, which is bought together with an RGB driver.
• LED sa nai-economy from the light source. Stored with LED lighting, connected to a 220 V network, can be switched on with a small switch.

RGB diode can yes be switched to blue light mode back kjm sdzharzhanieto ↑

How to choose LED strip for the kitchen

Illuminate the bodies in the kitchen hood and be protected from water and have an IP44, IP65 or IP67 protection class. This is especially important for onesi from the source on the light, which is located above the work surface and is close to the duskat, but they will illuminate the hearth in the dark. The voltage on the device is protected by 12 V.

Optimal nuance on light from LED lighting of the body trebva and be close to natural. Color temperature - 3300-5000 K.

The power on the LED behind the illumination on the work area is 4.8 W / m. For example, an SMD 3528 tape with a density of 60 LEDs / meter length.

Instead of a tape, you can choose LED modules with a higher power output. This is an electronic circuit with one or more LEDs, mounted on top of it in a sealed plastic case. These modules are all connected to the conductors one by one and are sold separately. The requirement for the design of the device can be chosen according to the installation time.

Natural color temperature - 3300-5000 K - answers to Svetlina byalata back kjm sdzharzhanieto ↑

Installation

With LED lighting, work on the floor, mount it under the wall cabinet, above the raft on the wall, using two types of lamps - LED modules and LED strip. Installed for everything from the source to the light and its own characteristics.

Mounting on LED modules

LED module for attaching to the surface through a special opening with a screw or small pironi. The module can be secured with double-sided tape.

Pass, which is tied to the body, while fixing the staples by the nails or position in the cable channel.They can and should be dressed up on parquet, equal to the distance between the illumination of the bodies, or yes, all the brocade has crawled out. In case they rule, open a page wall on the canal, someone guides them to harass.

Mounting on LED strip

LED lighting for the kitchen under the wardrobe fixed with a self-sealing layer on the hump. If you sculpt it dry, you can fasten it with a double-sided tape.

Important! For yes, prevent peeling off on tape, prejudicially before sticking, it is based on degreasing with alcohol or acetone. Comrade, pick up the hope for fixing it.

The body, which is tied with a self-adhesive tape, is fastened with staples by the nails.

LED tape can be installed in a special profile and even with a diffuser.

Montirana LED strip under the kitchen cabinet back kjm sdzharzhanieto ↑

Stupka on stupka process on a joint

Similar to mounting, the options for connection depend on the type of lighting used on the body. It is important that you install it before lampite. Ako sa is far from one another, togawa instead of a single unit, it can be a little more powerful. It is necessary to avoid a drop in the voltage in the conductor, and yes, they put the brightness on the lighting body. Another technically useful thing is the charge for the chorus, which they offend and rule everything in their own right. In a reasonable way, you can make a long and powerful LED strip not at the edges, but at the middle. They also painted the voltage drop in the print conductors and the product is evenly bright for the shine, it’s long.

Connection to LED modules

Diode modules are sold through sequentially connecting segments from the conductor. Ako dzhinata is not enough for them, then it is necessary for them to add conductors.

How do you direct it correctly with your own, the first step is described as a step by step:

1. determined by the necessary distance between modules;
2. cut off the brocade of a two-wire cable or two parchettes of a single strand, plus a length of plus 30 mm;
3. cut the conductor between the modules;
4. remove the edge from 15 mm;
5. put parquet from a heat-sealed pipe with a length of 25 mm at the top of the conductor;
6. twist the gi, which you will take up the anticipation of polarity;
7. put the parquet on the top with heat-sealed pipes;
8. flood gi ss sechoar.

It’s tied up on a conductor, it’s prescribing it, it’s being stored, it’s like sensory sensors, it’s a perverted way of starting.

Connecting LED strip

It is connected to the LED tape with two beginnings - connectors and soldering.

For yes, twist the connector, and it’s enough to expose the edges on the tape.

Conduct the connection through soldering in the following sequence:

1. remove the protective layer from the contact substrate;
2. kalaydisate platform with a kalaeno-tin calm, to use a neutral flow and a poyanik with a power that is not over 25 W;
3. take the parquet of bodies with the necessary length with a straight section of 0.35–0.5 mm2;
4. clean the edges with 5-7 mm;
5. kalaydiswana on clean zones;
6. put on top of the brocade jersey a heat-sealed pipe with a length of 30 mm;
7. drink zhitsata kjm lentata;
8. put the trabata on the ground on the solder and I warm up the ss sechoar.

You can direct your own lighting to the kitchen. The price of LED lighting the body together with the control chain is lower and it is not difficult to correct it. Comrade, pick up the lighting in the kitchen and direct the cooking in a convenient way.

PredishnaBacklight How to direct LED lighting for tavan or pervaz correctlyNextIlluminationSelection for a bathhouse with illumination