36W Fluorescent Lamp Specifications and Links

Title: Luminescent

fluorescent lamp Imagining a light source with a gas discharge, which caused the phenomenon of fluorescence, for which the light is visible. Predimstvata to use them: high efficiency and light power. Efficiency is 20-25%, dokato lamp with a pressurized zhichka imat itself 7%. Osvent tova te imat dalg exploitative belly. Such a light source can work from 15,000 to 20,000 hours, for a conventional light source, it can work about 1000. Nowadays, most of the light sources use a light source with a capacity of 36 watts.

Containment: 1. Device and principle for action 2. Characteristics and types of fluorescent lamps with a power of 36 watts 3. Scheme on the wire 4. Change to fluorescent lamp with LED lamp

Device and principle for action

The fluorescent lamp is made up of a sealed glass tube, sometimes containing argon gas at low pressure and a double cap of zhivak. Electricity is in it from two countries. Vtreshnata surface on the kolbat e covered with a thin layer of fluorescent dust. Coverage depends on the color, which is the product of choice. May be made from zinc silicate, cadmium silicate or calcium tungsten. These organic chemicals will turn invisible ultraviolet light into visible light.

Device and principle for action on a fluorescent lamp

Behind the back of the fluorescent lamp and shine, shake and apply a voltage of 500–2000 V to the electrode per 1 meter of the pipe. In this case, free up the electrons and fly along the rail to the electrode, which has a positive charge.When moving on the electronics, those ionizirates are gasified by atoms, which will fill the kolbat. Putting a yoni into the flowing gas will attract free electrons and light ultraviolet light. Under the action of this, si phosphoryt shine, that is, it is radiantly bright in the visible range.

You can read more for tov how to work in the tazi article -https://lux-en.housecope.com/vidy-i-tipy-lamp/lyuminestsentnaya/ll-ih-osobennosti

back kjm sdzharzhanieto ↑

Characteristics and types of fluorescent lamps with a power of 36 watts

Fluorescent lamp with 36w power for general application. Depending on the format, it is necessary to bivat linear or qdravi. They can use the light or defuse them.

Figurata along the length showing the markings on the local products.

Marking on a fluorescent lamp.

For the image, please enter two letters LB to show that the source of the daylight is in front of us.

Important! Fluorescent lamps LB are highly efficient in relation to light output.

Nai -widely used lamps to follow the radiation spectra:

• from the source for daylight light LD, as well as the technical analysis of LDT with improved color rendering;
• heating whites LTP lamps light pink tint of light;
• jelly white LHB technical specifications se amirate between LB and LD.

Nyama is the only global standard for branding, every company defines its products in its own way. Ordinarily European companies marked Svetlinniya spektar with figures. And so, the Osram company with the number 765 of the marker is student-colored, and 640 is topl. Philips TLD Do not follow the designations: 33 is the top flower, and 54 is the student (they can all be distinguished and essentially abbreviated from the Kelvin chilyad, for example 33 is 3300 K, and 54 is 5400 K).

Check for lighting with a power of 36 W and approximately follow the technical parameters:

• average brightness - from 6 to 11 cd / m2;
• Operating life at 36 W fluorescent lamp is less than 5000 hours. Average time to work - 12,000 hours;
• most cross a fluorescent linear lamp with twin capacs, long on a 1200 mm tube;
• usually imate a diameter for a pipe of 26 millimeters.
• Founded nai-chesto e G13, in order G5.

For yes, explain the technical characteristics of a particular product, try and consult with the documentation for it.

back kjm sdzharzhanieto ↑

Scheme on the wire

Fluorescent lamps cannot simply be switched on in the electrical network: for yes, it is brighter, the temperature on the electrode is shaking and it’s all over and yes, a short-term pulse with high voltage appears. For yes, send the tov, use the chain with an electromagnetic ballast (throttle and starter), which is better seen in tazi statia.

Scheme on a fluorescent lamp with throttle and starter

36w fluorescent lamp:

• Vednaga trace filed for warning, tokt soil and flow over the throttle, electrode electrode, starter, left electrode. In this case, the starter has a glow discharge and contact it heats up.
• Under the influence of this on the temperature, the bimetal contact on the starter is se ogva and ce s vyarzva from fixing.
• At the moment, at some point in contact with the connection, the resistance to the starter is brightly painted and the current in the verigata is increased.
• In order to increase the current, the electrode will heat up and heat up and cut off the electronics. Osvent tova's energy is saved on the throttle.
• Thy kato veche yama smoldering discharge into the starter, contact it will cool it and boil it.
• Once you make contact on the starter, they will open it, increasing the voltage on the throttle, increasing it for the sake of the EMF for self-induction. Receive a live bet from an electrical discharge and the trace is known to the time of the lamp on the ground and work in the working mode.

Tazi scheme on prevklyuchvane ima reditsa deficiencies.:

• impossible to turn on at low temperatures;
• noise at starter run and time to work;
• a lot of time for a starter, some increase from an increase in time for work on a product;
• Pulsirane on svetlinata by the time for work, somehow reflecting negatively on the healthy system of the viewer.

You can use the rope without chokes to wire the product, if you use the electronic ballast. The schematic on the link is usually drawn from the manufacturer's top case.

ECG per 36 watt fluorescent lamp back kjm sdzharzhanieto ↑

Change on fluorescent tubes with LED

Wrinkled on a fluorescent light source with an LED lamp osiguryava double energy savings, as well as eliminating external noise. Yes, yes change fluorescent lamp On the LED, it is desirable that they have a single and basic basis G13 (in a row, yes, there can be G5), but this catotove is not artificially changed on the cassette. If your lamp is an electronic ballast, try to get rid of the verigat and let the lamp be direct to 220V.

A typical circuit for connecting LED lamps

For yes, replace the source with a light in an old style lamp with an electronic ballast, that is, with an ordinary throttle and a starter, you need from:

1. Get the starter out.
2. Get rid of the throttle from the verigat or contact me.
3. Install the LED lamp.

Starter trebva yes bjde dumped, for yes sbegne koso connection when turned on.

Scheme for the change to the lighting rod from the luminescent tube of the LED lamp PredishnaFluorescent Circuitry and Characteristics for 18 W Fluorescent LampsNextLuminescent type fluorescent lamp with G13 base and technical characteristics